NACE-CIP1-001 PDF Dumps Real 2026 Recently Updated Questions
Released NACE NACE-CIP1-001 Updated Questions PDF
NEW QUESTION # 32
How many gauge readings does SSPC-PA 2 require within a 4 cm (1.5 inch) diameter circle?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION # 33
Removal of surface contaminants is done by:
- A. A combination of methods
- B. Abrasive blasting
- C. Waterjetting
- D. Scarifying
Answer: A
NEW QUESTION # 34
An inspectors personal log book should contain:
- A. No comments regarding the application team
- B. The inspector's personal opinions of the application team
- C. Objective comments regarding the application work
- D. Subjective comments re ding the application team
Answer: A
NEW QUESTION # 35
To be of value the Inspector's documentation must be:
- A. Timely, accurate and concise
- B. Always handwritten
- C. Submitted before the end of the job
- D. Always typewritten
Answer: A
NEW QUESTION # 36
What is used to determine compressed air cleanliness?
- A. Blotter test
- B. Needle pressure gauge
- C. Psychrometer
- D. Profilometer
Answer: D
NEW QUESTION # 37
The most important factor resulting in improved job site safety is:
- A. Safety Enforcement
- B. Situational Awareness
- C. Engineering Controls
- D. Personal Protective Equipment
Answer: B
NEW QUESTION # 38
Conventional spray is a good choice when:
- A. High quality finishes are required
- B. High production rates are required
- C. High transfer efficiency is required
- D. High viscosity coatings are being applied
Answer: A
NEW QUESTION # 39
You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:
- A. Skip the checks and just record the same readings as you have been getting
- B. Keep doing the checks and consult the Owner's representative for direction
- C. Skip the checks as you are. confident the blast pressure is OK
- D. Keep doing the checks regardless
Answer: B
NEW QUESTION # 40
Whenever dissimilar metals must join, the most common practice is to
- A. avoid coating all connected dissimilar metals.
- B. provide cathodic protection to prevent corrosion,
- C. provide anodic protection to prevent corrosion.
- D. coat all connected dissimilar metals.
Answer: D
NEW QUESTION # 41
An Inspector should change position when:
- A. Only when directed by the supervisor
- B. The Inspector is convinced by verifiable facts
- C. The Inspectors position is not the majority position
- D. The Owner can save some money by the change
Answer: B
NEW QUESTION # 42
When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:
- A. Achieve consensus through negotiation
- B. Call the supervisor
- C. Go with the majority opinion
- D. Never change his/her mind
Answer: B
NEW QUESTION # 43
Safety Data Sheets must be carefully reviewed by:
- A. The Inspection personnel
- B. The Owner's personnel
- C. All personnel involved in the job
- D. The Application personnel
Answer: C
NEW QUESTION # 44
Galvanic corrosion occurs on which of the following substrates:
- A. Concrete
- B. Wood
- C. Metal
- D. Fiberglass Reinforced Plastic
Answer: C
NEW QUESTION # 45
Check abrasive blast pressure with a
- A. needle pressure gauge
- B. nozzle aperature gauge
- C. surface comparator
- D. replica tape
Answer: A
NEW QUESTION # 46
Corrosion generally occurs at which of the following sites:
- A. Anode
- B. Metallic pathway
- C. Electrolyte
- D. Cathode
Answer: A
NEW QUESTION # 47
......
NACE-CIP1-001 Dumps and Practice Test (100 Exam Questions): https://www.test4cram.com/NACE-CIP1-001_real-exam-dumps.html
Guide (New 2026) Actual NACE NACE-CIP1-001 Exam Questions: https://drive.google.com/open?id=1lH4NeiP_plVgCxpiZ1Ilx5Rf68pADQ2t