Use Real NS0-183 - 100% Cover Real Exam Questions [Oct-2021]
Dumps Brief Outline Of The NS0-183 Exam - Test4Cram
NEW QUESTION 75
In an ONTAP switched cluster, which three types of traffic travels over the cluster network? (Choose three.)
- A. intercluster SnapMirror
- B. remote cluster peering
- C. cluster database replication
- D. intracluster SnapMirror
- E. Epsilon voting
Answer: A,B,C
NEW QUESTION 76
You have a 6-node ONTAP 9.1 cluster with two FAS6290 nodes and four FAS8080 EX nodes using a SAN protocol.
In this scenario, how many FAS9000 HA pairs would be joined to this cluster?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION 77
What is the default shelf ID for disk shelves with IOM12 modules?
- A. 01
- B. 00
- C. 0
- D. 1
Answer: B
NEW QUESTION 78
You are preparing for a new installation. While determining the most suitable version of ONTAP software to deploy, you want to verify the ONTAP 9 release cadence to ensure that you are deploying a Long Term Service (LTS) release.
In this scenario, where would you find this information?
- A. Visit the Hardware Universe site.
- B. Visit the NetApp Support site.
- C. Visit the ONTAP 9 Documentation Center site.
- D. Visit the Interoperability Matrix Tool site.
Answer: C
NEW QUESTION 79
Click the Exhibit button.
You are receiving AutoSupport e-mail from both controllers, but Active IQ is showing updates from only node cl-01-02.
Referring to the exhibit, what is a reason why Active IQ is receiving AutoSupport updates from only node cl-01-02?
- A. The service processor is not configured.
- B. A firewall rule is blocking the AutoSupport.
- C. The cluster management LIF is down.
- D. The mail host is blocking the AutoSupport.
Answer: B
NEW QUESTION 80
What are two ONTAP storage efficiency technologies that would be used on an AFF A400 cluster?
(Choose two.)
- A. FlexClone volumes
- B. FlashCache
- C. thin provisioning
- D. Flash Pool
Answer: B,D
NEW QUESTION 81
What are two reason why automatic giveback fails? (Choose two.)
- A. SAN sessions are established.
- B. Storage failover is disabled.
- C. The disk shelf is too hot.
- D. NFS sessions are established.
Answer: B,C
NEW QUESTION 82
You complete a hardware installation on a CN1610 switch and establish a serial connection to the RJ45 port.
In this scenario, the established serial connection allows the installer to complete which two tasks for the switches initial configuration? (Choose two.)
- A. to use the serial port connection as a diagnostic channel to the second CN1610 switch in the cluster interconnect
- B. to configure the switch with another CN1610 switch using Cross-Stack EtherChannel configuration for load balancing and performance
- C. to manually configure the static network information
- D. to view network information that has been dynamically assigned to the management interface by the DHCP server on the network
Answer: C,D
NEW QUESTION 83
You have to disable a switch that is connected to a port on your FAS2750. You notice that the LIFs that are associated with this port are migrated to a port that is not expected.
In this scenario, what would cause this behavior?
- A. There are no online ports within the same failover group.
- B. The network port is configured incorrectly.
- C. The broadcast domain is configured incorrectly.
- D. The network failover port is not licensed.
Answer: C
NEW QUESTION 84
You want to verify that connections are cables correctly and that shelf IDs are unique within an HA pair.
Which tool would be used to accomplish these tasks?
- A. Active IQ Config Advisor
- B. System Diagnostics
- C. Cloud Insights
- D. Active IQ Unified Manager
Answer: B
NEW QUESTION 85
You are adding new controllers to an existing cluster. As part of the upgrade process, you have updated the BES-53248 cluster switches.
In this scenario. Which two commands would you use to verify a healthy cluster after the upgrade? (Choose two.)
- A. network port show -ipspace Cluster
- B. network interface show -vserver Cluster -fields auto-revert
- C. network interface show -vserver Cluster
- D. network device-discovery show -protocol cdp
Answer: A,C
NEW QUESTION 86
An ONTAP cluster is installed at a secure site. The array has no access to the Internet but is managed 24/7 by onsite engineers. The customer requires that when hardware failures occur, the failures are reported to the NetApp Support team as quickly as possible.
In this scenario, which two tasks should be performed during the project hand-off procedure to satisfy the customer's requirement? (Choose two.)
- A. Ensure that the onsite engineers receive EMS alerts when hardware issues occur.
- B. Educate the onsite engineer about how to manually log support calls.
- C. Ensure that Active IQ Config Advisor is installed.
- D. Educate the onsite engineers about invoking the AutoSupport tool from ONTAP System Manager.
Answer: A,D
NEW QUESTION 87
You install a new FAS2650 HA with a DS224C disk shelf and ONTAP 9.5 on a customer site.
Referring to the exhibit, which steps are required to get an HA cabled system?
- A. 1. Insert a cable from right controller port 0a to IOMB port 2, and from port 0b to IOMA port 4. 2. Insert a cable from left controller port 0a to IOMA port 2, and from port 0b to IOMB port 4. 3. Cable the out-of-band ACP.
- B. 1. Insert a cable from right controller port 0a to IOMA port 1, and from port 0b to IOMB port 3. 2. Insert a cable from left controller port 0a to IOMB port 1, and from port 0b to IOMA port 3.
- C. 1. Insert a cable from right controller port 0a to IOMB port 2, and from port 0b to IOMA port 3. 2. Insert a cable from left controller port 0a to IOMA port 2, and from port 0b to IOMB port 3.
- D. 1. Insert a cable from right controller port 0a to IOMB port 1, and from port 0b to IOMA port 4. 2. Insert a cable from left controller port 0a to IOMA port 1, and from port 0b to IOMB port 4. 3. Cable the out-of-band ACP.
Answer: B
NEW QUESTION 88
Which two commands verify that AutoSupport is working as expected?
- A. autosupport check show
- B. autosupport show
- C. autosupport test show
- D. autosupport history show
Answer: A,D
NEW QUESTION 89
What are two types of load balancing methods available in multimode interface groups? (Choose two.)
- A. port-based load balancing
- B. broadcast domain-based load balancing
- C. LIF-based load balancing
- D. IP-based load balancing
Answer: A,D
NEW QUESTION 90
Click the Exhibit button.
You have an 8-node cluster, and sometimes the data LIFs fail over to a non-working port.
Referring to the exhibit, what must you do to solve this problem?
- A. Configure more than one IPspace.
- B. Configure the MTU consistently across the cluster.
- C. Configure the LIFs using separate home nodes.
- D. Configure the correct Ethernet ports in all broadcast domains.
Answer: B
NEW QUESTION 91
In ONTAP 9.7 software, how many different replicated databases (RDBs) exist per node?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION 92
You have just finished installing and configuring an ONTAP cluster for a customer.
In this scenario, which product collects information and produces site documentation?
- A. Active IQ OneCollect
- B. Inventory Collect Tool
- C. SnapGathers
- D. NetAppDocs
Answer: D
NEW QUESTION 93
Which NetApp tool relies on PowerShell to produce a comprehensive handover report to the customer?
- A. Fusion
- B. NetAppDocs
- C. Config Advisor
- D. Active IQ
Answer: B
NEW QUESTION 94
......
Certification Training for NS0-183 Exam Dumps Test Engine: https://www.test4cram.com/NS0-183_real-exam-dumps.html